GMC Canyon and Chevrolet Colorado Engine removal Procedure?

How to replace Engine for Chevy Colorado Or How to replace Engine for GMC Canyon.

The procedure is same.
The details are as follows:-----


Engine
REMOVAL & INSTALLATION mentioned below:----

1. Disconnect the battery cables and properly relieve the fuel system pressure.
2. Drain the engine cooling system.
3. Drain the engine oil.
4. Remove or disconnect the following:
   
   NOTE

   Reinstall the engine lift bracket after removing the alternator. Tighten the bolts to 44 inch lbs. (5 Nm) and then retighten to 37 ft. lbs. (50 Nm).
   
   
   
   
   Hood

   Battery box

   Radiator hoses

   Cooling fan

   Air cleaner assembly

   Engine lifting bracket

   Alternator
   
   
   
   
   Washer reservoir bolts

   Engine wiring harness connector at PCM

   Wiring harness retainers at fender, power steering pump, throttle body and camshaft cover

   Oil pressure switch connector

   4WD motor connector, if equipped

   Camshaft Position (CMP) sensor connector

   Exhaust camshaft actuator connector

   Coolant temperature sensor connector

   Injector harness connector

   Ignition coil connectors

   Oxygen Sensor (O ₂ S) connector

   Wiring harness conduit at camshaft cover

   Automatic transmission filler tube, if equipped

   Air injection pipe cover

   Install engine lifting eye in air pipe cover location

   Heater hoses from heater core

   A/C suction hose bracket

   Power steering pump bolts and position pump aside

   Right engine mount-to-frame bracket bolt

   Wiring harness retainer from intake manifold and position aside

   Fuel lines from fuel rail

   Evaporative pipe at intake manifold

   Dipstick and tube

   Brake booster hose

   Manifold Absolute Pressure (MAP) sensor

   MAP wiring harness retainer

   Upper 2 engine wiring harness bracket bolts

   Raise and support vehicle

   Left front wheel

   Left front fender inner liner

   Wiring harness retainers from engine wiring bracket

   Engine wiring harness bracket

   A/C compressor mounting bolts and position compressor aside

   Starter wiring

   Negative battery cable from block

   EVAP canister connector

   Knock sensor connectors

   Heater outlet hose

   Crankcase Position (CKP) sensor connector

   Engine wiring ground leads from block

   Engine wiring harness retainer at oil pan rail and position harness aside

   Catalytic converter

   Exhaust donut gasket

   Automatic transmission oil cooler and fuel line brackets, if equipped

   Left engine mount-to-frame bracket bolt

   On 2WD drive models, front crossmember

   On 4WD models, differential carrier

   On automatic transmission, torque converter bolts after marking torque converter-to-flexplate location

   Leave 2 upper transmission-to-engine bolts, but remove all other bolts
5. Lower the vehicle and place a transmission jack under the transmission
6. Remove the remaining transmission mounting bolts
7. Install a suitable lifting device to the engine.
8. Remove the engine mount bolts and carefully lift the engine from the vehicle. Pause several times while lifting the engine to make sure no wires or hoses have become snagged.

To install:

1. Carefully lower the engine into the vehicle and align the engine dowels with the transmission.
2. Install the engine mount bolts and tighten the bolts to 37 ft. lbs. (50 Nm).
3. Lower the engine onto the engine mounts.
4. Remove the engine lifting device.
5. Raise and support the vehicle.
6. Install the transmission-to-engine bolts and tighten the bolts to 37 ft. lbs. (50 Nm).
7. Remove the transmission jack.
8. Aligning the torque converter to the flexplate, install the bolts and tighten to 44 ft. lbs. (60 Nm).
9. On 2WD, install the crossmember and tighten the bolts to 44 ft. lbs. (60 Nm).
10. On 4WD, install the differential carrier.
11. Install or connect the following:
    
    
    Automatic transmission oil cooler and fuel line brackets, if equipped

    Left engine mount-to-frame bracket bolt and tighten to 63 ft. lbs. (85 Nm).

    New exhaust donut gasket

    Catalytic converter and tighten the bolts to 37 ft. lbs. (50 Nm).

    Engine wiring harness retainers at oil pan rail

    Engine wiring ground leads to block

    CKP sensor connector

    Heater outlet hose

    Knock sensor connectors

    EVAP canister connector

    Negative battery cable to block

    Starter wiring

    A/C compressor mounting bolts tighten the bolts to 37 ft. lbs. (50 Nm)

    Engine wiring harness bracket

    Wiring harness retainers from engine wiring bracket

    Left front fender inner liner

    Left front wheel

    Lower the vehicle

    Upper 2 engine wiring harness bracket bolts

    MAP wiring harness retainer

    MAP sensor

    Brake booster hose

    Dipstick and tube

    Wiring harness retainer to intake manifold

    Evaporative pipe at intake manifold

    Fuel lines to fuel rail

    Right engine mount-to-frame bracket bolt and tighten bolt to 63 ft. lbs. (85 Nm)

    Power steering pump

    A/C suction hose bracket

    Heater hoses from heater core

    Remove engine lifting eye in air pipe cover location

    Air injection pipe cover using new gasket

    Automatic transmission filler tube

    Wiring harness conduit at camshaft cover

    Wiring harness retainers at fender, power steering pump, throttle body and camshaft cover

    Coolant temperature sensor connector

    Injector harness connector

    Ignition coil connectors

    Oxygen Sensor (O ₂ S) connector

    Exhaust camshaft actuator connector

    CMP sensor connector

    4WD motor connector, if equipped

    Oil pressure switch connector

    Engine wiring harness connector at PCM

    Washer reservoir bolts

    Alternator

    Engine lifting bracket

    Air cleaner

    Cooling fan

    Radiator hoses

    Battery box

    Hood
12. Check all powertrain fluid levels and add, as necessary. Be sure to properly fill the engine crankcase with clean engine oil.
13. Connect the battery cables and properly fill the engine cooling system.
14. Start and run the engine, then check for leaks.

These details will help.

Thanks.           

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html