BannerFans.com

Friday, April 20, 2012

Control Cables Details and Replacing for Dodge and Chrysler?

The AC/Heater HVAC control panel details and replacing.
The Door actuator control cable details and procedure.

Please Note that this Procedure Covers all U.S. and Canadian models of the Chrysler/Dodge Avenger, Chrysler Sebring Coupe and Dodge Stratus/ Stratus Coupe models for Year 1999 to 2005.


The details and procedure with Helpful diagram is as follows:---

1999-00 models use cables to actuate the temperature door and recirculation doors. 2001-05 models use actuators instead of cables. For servicing the actuators refer to the Blend Door Actuator and Recirculation Door Actuator sections of this product.


Recirculation Door Cable



The cables must be adjusted for proper function of the control module. To adjust the cable, attach the cable to the lever arm of the control module. Turn the knob fully counterclockwise. Pull the cable jacket away from the cable end until taut. Clip the cable jacket to the control module. The knob should travel a full 180° if the cable is properly adjusted.
The RECIRC door is actuated by a cable which mechanically positions the door.
The RECIRC door actuator is located at the far right of the A/C Heater housing near the right A-pillar.
image
Fig. Temperature door cable (1), control module (2), A/C housing (3) and recirculation door cable (4)
  1. Place the ignition key in the OFF position before removing control module.
  2. Remove the trim bezel. 

    image
    Fig. Typical trim bezel
  3. Remove the cluster hood bezel retaining screws in the trim bezel opening.
  4. Pry up the cluster hood bezel a few inches to expose the cubby bin/cigar lighter bezel screws.
  5. Remove the cubby bin/cigar lighter bezel and wiring.
  6. Remove the control module retaining screws.
  7. Drop the A/C control module into the cigar lighter/cubby bin bezel opening then disconnect the wiring on the rear of the control module.
  8. Release the recirculation cable retaining clip from the top of the control module. Retain the clip for future use. Then disconnect the recirculation control cable.
  9. Remove the right under panel silencer/duct.
  10. Disconnect cable flag at right of recirculation housing. 
    image

    Fig. Disconnecting recirculation door cable (1)
  11. Remove the cable core end from recirculation actuator lever.
To install:
Install the in reverse order of removal. Verify that the cables are properly adjusted, free of interference and the module is seated properly.

Temperature Door Cable



The blend-air (temperature) door is actuated by a cable which mechanically positions the temperature door.
The temperature door actuator is located at the center of the A/C Heater housing at the center tunnel.
image
Fig. Temperature door cable (1), control module (2), A/C housing (3) and recirculation door cable (4)
  1. Place the ignition key in the OFF position before removing control module.
  2. Remove the trim bezel 

    image
    Fig. Typical trim bezel
  3. Remove the cluster hood bezel retaining screws in the trim bezel opening.
  4. Pry up the cluster hood bezel a few inches to expose the cubby bin/cigar lighter bezel screws.
  5. Remove the cubby bin/cigar lighter bezel and wiring.
  6. Remove the control module retaining screws.
  7. Remove the control module and disconnect the wire connectors.
  8. Release the temperature control cable retaining clip from the top of the control module. Retain the clip for future use. Then disconnect the temperature control cable.
  9. Disconnect cable at A/C housing. 

    image
    Fig. Temperature cable at A/C housing
  10. Remove the cable core end from temperature actuator lever.
To install:
Installation is the reverse of removal.

These details will help.
Thanks.           

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html


No comments:

Post a Comment